If not, equivalent substitutes must be used. Refer to hereunder Figure 2 to know the figure s No s corresponding to the code number of your valve. The The nominal range of a spring-diaphragm specific operating conditions and environmental actuator is the air pressure range in pounds per conditions will also impact the useful life of the square inch psi for rated stroke under no load. SIowly and squarely, lower the bonnet 7 over the plug stem 1body studs 21 and into the bolting position. Hamad Khaled. Figure 2 Fig.
Technical Specifications. 05/ GE Oil & Gas. Masoneilan* Valves. 37/38 Pneumatic Spring.
Actuator 37 38 GE Masoneilan Technical Specification Steel Actuator
Diaphragm Actuator. The 37/38 Series actuator is designed to. Actuator 37 38 GE Masoneilan Instruction Manual - Read online for free.

Actuator 37 38 GE Masoneilan Instruction Manual. Documents Similar To Actuator 37 38 GE Masoneilan Technical Specification. Uploaded by. KJ Supply.
Cutui Marius. Qty Length mm Dia. Note : Intermittent lifting is important to keep the plug and seat concentric during lapping. Indeed, the original pin hole in an old stem prevents satisfactory results and might seriously impair strength of the assembly.
Actuator 37 38 GE Masoneilan Technical Specification Steel Actuator
Slightly release air pressure and tighten stem locknuts 27 against actuator stem [or locking plate 55 ].
Computer Ref. Laboratorium CNC.
![]() Winchell lake mn dnr |
If the ring is not continuous, repeat the entire lapping operation until the ring is continuous.
In all cases, slide the first set of rings along the plug then insert it into the lower groove. Video: Masoneilan actuator 37 pdf free ENGIE Fabricom - Masoneilan SVI II AP positioner Amit Patel. If no ADD. CIean the valve parts thoroughly before reassembling. |

. Jebel Ali Free Zone. Masoneilan has a highly skilled After Sales Department available for start-up Mounted on Series 37 / 38 Spring Diaphragm Actuators. (Only for valve strokes . The following conditions are necessary for trouble-free operation: 1. Proper. MIL - Pneumatic Spring Diaphragm.

Actuators with optional hand wheels. Sizes: 11", 13", 15", 18" & 24". Travel: <4".
Masoneilan+++and++ Valve Electrical Connector
Supply Pressure: 20 to 65 psig.
Guide Section 9. Increase air pressure to retract actuator stem about 1,5 mm. Tighten capscrews simultaneously and progressively until the retaining ring 19 can be removed. Proceed as described in the above paragraph D2, taking care not to damage the plug shank area.
Actuator 37 38 GE Masoneilan Instruction Manual Actuator Valve
Connections are Replace washer 41nut 30 and upper diaphragm located in the upper diaphragm case air-to- case. The spring range and maximum allowable supply pressure are marked on the serial plate.
![]() GAME4V GOALUNITED NEXT |
Packing box maintenance is one of the principle chores of routine servicing.
PIace the plug shank on a V-block and, using a size of drill bit suitable to either, match the hole size in the plug, or match the C diameter see Figure 6drill the plug-stem assembly. Do not damage seat ring. Adjust travel indicator scale 56 : travel indicator 58 should indicate open when air pressure is relieved. Apply a light coat of a lubricant, such as Gripcott NF or equivalent to the body studs threads and the bearing surfaces of the body stud nuts 8. |
Replacing Plug and Stem The plug 15 and stem 1 assembly consists of a shaft threaded into the plug and pinned in place.
Ex : for the 6 valve size, total stem retraction would be : 8 mm.